m5p3nc3r/ros-raspbot-v2

Fork 0

Files

T

m5p3nc3r 2fcf8ce26b Refactor from my_robot to raspbot-v2

2026-04-16 22:08:52 +00:00

10 KiB

Raw Blame History

raspbot_v2

ROS 2 package for the Yahboom Raspbot V2 platform — differential-drive motor control and pan/tilt camera orientation.

Architecture

Both nodes share the same I²C bus. The Linux kernel serialises individual transactions, so they can run as separate processes without additional locking.

Motor controller

                      ┌───────────────────────────────────┐
                      │      MotorControllerNode          │
                      │                                   │
 /cmd_vel  ──────────>│  Twist → differential kinematics  │
 (geometry_msgs/Twist)│  left  = linear − (angular × wb/2)│
                      │  right = linear + (angular × wb/2)│
                      │                                   │
 /wheel_speeds ──────>│  Direct per-wheel override        │
 (Float32MultiArray   │  [FL, FR, RL, RR]                 │
  4 × float32)        │                                   │
                      │         ▼                         │
                      │   raspbot_v2_interface            │
                      │   I²C bus 1, addr 0x2B            │
                      │         ▼                         │
                      │   /dev/i2c-1 ─────────> Motors    │
                      │                                   │
 /current_wheel_speeds│<─ telemetry @ 10 Hz               │
 (Float32MultiArray)  │   [FL, FR, RL, RR]                │
                      └───────────────────────────────────┘

Topics

Topic	Direction	Type	Description
`/cmd_vel`	Subscribed	`geometry_msgs/Twist`	Velocity command — `linear.x` (m/s) and `angular.z` (rad/s)
`/wheel_speeds`	Subscribed	`std_msgs/Float32MultiArray`	Direct per-wheel speed override `[FL, FR, RL, RR]` in library units (0–255)
`/current_wheel_speeds`	Published	`std_msgs/Float32MultiArray`	Current wheel speeds read from hardware, published at 10 Hz

Parameters

Parameter	Default	Description
`wheel_base`	`0.3`	Distance between left and right wheels in metres
`max_speed`	`1.0`	Maximum motor speed in library units

Camera orientation controller

                         ┌──────────────────────────────────────┐
                         │      CameraOrientationNode           │
                         │                                      │
 /joint_command  ────────>│  JointState (names: pan, tilt)      │
 (sensor_msgs/           │  position in radians                 │
  JointState)            │                                      │
                         │  pan  → servo 1  (0°–180°)          │
                         │  tilt → servo 2  (0°–110°)          │
                         │                                      │
                         │         ▼                            │
                         │   raspbot_v2_interface               │
                         │   I²C bus 1, addr 0x2B               │
                         │         ▼                            │
                         │   /dev/i2c-1 ──────> Pan/tilt servos │
                         │                                      │
 /joint_states   <────────│  current angles @ 10 Hz             │
 (sensor_msgs/           │  position in radians                 │
  JointState)            │                                      │
                         └──────────────────────────────────────┘

Topics

Topic	Direction	Type	Description
`/joint_command`	Subscribed	`sensor_msgs/JointState`	Commanded pan/tilt angles. Joint names `"pan"` and `"tilt"`, positions in radians. Unknown joint names are ignored.
`/joint_states`	Published	`sensor_msgs/JointState`	Current angles reflected from the last command, published at 10 Hz

Parameters

Parameter	Default	Description
`pan_servo_id`	`1`	Raspbot servo channel for pan
`tilt_servo_id`	`2`	Raspbot servo channel for tilt
`pan_min_deg`	`0.0`	Pan lower limit (degrees)
`pan_max_deg`	`180.0`	Pan upper limit (degrees)
`tilt_min_deg`	`0.0`	Tilt lower limit (degrees)
`tilt_max_deg`	`110.0`	Tilt upper limit (degrees) — hardware cap
`pan_center_deg`	`90.0`	Startup and shutdown park position for pan
`tilt_center_deg`	`60.0`	Startup and shutdown park position for tilt
`state_rate_hz`	`10.0`	`~/joint_states` publish rate

Hardware interface

The node drives the pan and tilt servos over I²C bus 1 (device address 0x2B). The same /dev/i2c-1 device used by the motor controller is sufficient — no additional device node is required.

Setting up the robot

1. Flash Raspberry Pi OS

Use the Raspberry Pi Imager to write Raspberry Pi OS (64-bit, Lite recommended) to a microSD card.

Before writing, open the imager's Advanced options (⚙) and configure:

Setting	Value
Hostname	`raspbot-v2.local`
SSH	Enabled
Username / Password	Your preferred credentials
Wi-Fi	Your network SSID and password (if not using Ethernet)

Write the image, insert the card, and power on the Pi. Once it has booted and is reachable on the network (test with ping raspbot-v2.local), proceed to the next step.

2. Provision with Ansible

The ansible/ directory contains a playbook that handles the remaining setup (enabling SPI, installing Docker). See ansible/README.md for full instructions.

Building

Prerequisites

Docker (with BuildKit enabled)
For cross-compilation from an amd64 host, QEMU user-space emulation must be registered with the kernel. If you haven't done this before, run once:
```
docker run --rm --privileged tonistiigi/binfmt --install arm64
```

Build the image

The Raspberry Pi is arm64, so the image must be built for that platform. On an amd64 host use docker buildx:

docker build --platform linux/arm64 -t raspbot_v2:latest .

--load exports the built image into the local Docker image store so it can be deployed with docker save.

The build is split into two stages:

builder — installs the Raspbot hardware library, then compiles the ROS package with colcon
runtime — copies only the colcon install overlay and hardware library into a clean ros:kilted base; no build tools are included in the final image

Deploying

Once the image is built, pipe it directly to the target over SSH — no intermediate file or registry needed:

docker save raspbot_v2:latest | ssh matt@raspbot-v2.local docker load

Replace matt with the username configured in ansible/inventory.ini.

Launching

The default CMD starts both nodes together via the launch file. The container needs access to the I²C bus — pass only that device rather than running privileged:

docker run --rm \
  --network=host \
  --device /dev/i2c-1 \
  --env ROS_DOMAIN_ID=0 \
  raspbot_v2:latest

If your board exposes the controller on a different bus (check with ls /dev/i2c-* on the host), substitute the correct device node (e.g. --device /dev/i2c-0).

Overriding parameters at launch

Launch arguments can be appended after the image name:

docker run --rm \
  --network=host \
  --device /dev/i2c-1 \
  --env ROS_DOMAIN_ID=0 \
  raspbot_v2:latest \
  ros2 launch raspbot_v2 robot.launch.py \
    wheel_base:=0.25 max_speed:=0.8 tilt_center_deg:=45.0

Available launch arguments:

Argument	Default	Description
`wheel_base`	`0.3`	Distance between left and right wheels (m)
`max_speed`	`1.0`	Maximum motor speed in library units
`pan_center_deg`	`90.0`	Pan angle at startup and shutdown (degrees)
`tilt_center_deg`	`60.0`	Tilt angle at startup and shutdown (degrees)

Sending velocity commands from the host

With the container running, publish from another terminal (requires ROS 2 on the host or a second container on the same network):

# Drive forward at 0.2 m/s
ros2 topic pub --once /cmd_vel geometry_msgs/msg/Twist \
  "{linear: {x: 0.02}, angular: {z: 0.0}}"

# Turn on the spot
ros2 topic pub --once /cmd_vel geometry_msgs/msg/Twist \
  "{linear: {x: 0.0}, angular: {z: 0.5}}"

# Stop
ros2 topic pub --once /cmd_vel geometry_msgs/msg/Twist \
  "{linear: {x: 0.0}, angular: {z: 0.0}}"

Commanding the camera from the host

Pan to centre (90°) and tilt to 30°:

ros2 topic pub --once /joint_command sensor_msgs/msg/JointState \
  "{name: ['pan', 'tilt'], position: [1.5708, 0.5236]}"

A single axis can be commanded by omitting the other joint name:

# Pan only
ros2 topic pub --once /joint_command sensor_msgs/msg/JointState \
  "{name: ['pan'], position: [0.0]}"

Verifying telemetry

# Wheel speeds
ros2 topic echo /current_wheel_speeds

# Camera orientation
ros2 topic echo /joint_states

Project layout

.
├── Dockerfile                  # Two-stage production image
├── docker-entrypoint.sh        # Sources ROS overlays before exec
├── src/
│   └── raspbot_v2/
│       ├── package.xml         # ROS package manifest
│       ├── setup.py            # ament_python build definition
│       ├── launch/
│       │   └── robot.launch.py               # Starts both nodes together
│       └── raspbot_v2/
│           ├── __init__.py
│           ├── motor_controller_node.py      # Differential-drive motor control
│           └── camera_orientation_node.py    # Pan/tilt servo control
└── raspbot_v2_interface/       # Vendored Yahboom hardware library
    └── Raspbot_Lib/
        └── Raspbot_Lib.py      # I²C driver (smbus, bus 1, addr 0x2B)

10 KiB Raw Blame History Unescape Escape

raspbot_v2

Architecture

Motor controller

Topics

Parameters

Camera orientation controller

Topics

Parameters

Hardware interface

Setting up the robot

1. Flash Raspberry Pi OS

2. Provision with Ansible

Building

Prerequisites

Build the image

Deploying

Launching

Overriding parameters at launch

Sending velocity commands from the host

Commanding the camera from the host

Verifying telemetry

Project layout

10 KiB

Raw Blame History